Flowserve 10-40 39 Access M Worcester Controls Manual de usuario descargar pdf (Pagina 1)

FCD WCAIM2034-01

(Part 17256)

Worcester Controls 10-40 39 Access M

Mounted Limit Switch (Proximity Sensor) and Solenoid

Installation, Operation and Maintenance Instructions

When shipped for field installation, the limit switch (proximity

sensor)/solenoid assembly will be broken down into subassemblies.

The subassemblies are: (1) the switch (sensor) operator assembly,

consisting of the switches (sensors), bracket, springs and buttons;

and (2) the enclosure (housing), probes, solenoid (if applicable),

control block or air connection block, block gasket, PC board or

terminal strip and cover. Hardware items and gasket are packaged

separately. Retaining rings and O-rings shall be assembled.

Ambient temperature range of Access unit is 0°F minimum to 160°F

maximum.

NOTE: Access M Mounted Limit Switch (Proximity Sensor)/Solenoid

Kits fit only Revision R5 and later 39 Actuators. Included in the

Access M Mounted Limit Switch (Proximity Sensor)/Solenoid Kits is a

Rebuild/Accessory Addition Label which is to be marked and applied

to actuator after switch has been installed.

1. The Access M Mounted Limit Switch (Proximity Sensor)/Solenoid

assembly will be mounted on the right-hand end cap (when

viewed from actuator nameplate) with conduit connection on the

right side of the housing (when viewed from the cover side of the

switch).

CAUTION: When actuator is installed in outdoor conditions, water

can enter the exhaust hole(s) of the control block or air connection

block, and then freeze. Flowserve suggests a cover be used, or

mount the actuator such that the block exhaust hole(s) will not fill

with water.

The “standard” mounting configuration of the 39 actuator to the

valve is in-line, fail-closed. In this configuration, SW-1, as

described in Section 6 and in the wiring diagram, will give

indication when the actuator is in the open position (green LED is

on), or CCW (counterclockwise) limit of rotation. SW-2 gives

indication of the closed position (red LED is on), or CW

(clockwise) limit of rotation. See Section 8 for appropriate wiring

diagram.

NOTE: The CW or CCW rotation of the actuator shaft is determined

when viewing the actuator from the nameplate side of the actuator,

while being able to read the label from left to right.

Fail-open mounting configuration may be obtained by either

inverting the actuator, using in-line coupling or mounting the

actuator cross-line (sizes 10-20) or indexing the coupling

(including valve ball and stem) 90° to the actuator shaft (sizes 25-

40). In these cases SW-2, as described in Section 6 and in the

wiring diagram, will give indication when the actuator is in the

open position (green LED is on). SW-1 gives indication of the

closed position (red LED is on). Actuator shaft rotation will vary,

depending on which fail open mounting is used. See Section 8 for

appropriate wiring diagram.

NOTE: LEDs not offered with 240 VAC single-voltage units.

Printed circuit boards (LEDs) not offered with proximity sensors.

The fail-open wiring diagrams in Section 8 and adjustments in Section

6 are for cross-line or 90° indexed mountings only. For wiring and

adjustments of other fail closed or fail open configurations consult

Flowserve.

2. Remove cover from enclosure.

CAUTION: The longer probe must be in the left hand through-hole

looking at the housing from the cover side. (Both probes are the

same length for the 1039 ACCESS only!)

3. Assemble the enclosure, with probe assemblies, to the actuator

inserting the housing gasket between the actuator end cap and

the housing. Important! Do not apply any grease to the gasket, it

must be installed dry. Secure with four machine screws. For all

ACCESS M units, four threaded tamper proof plugs are installed

over the machine screws. Once installed, no attempt should be

made to remove these plugs. If it becomes necessary to remove

enclosure from actuator end cap, consult Flowserve. Check the

probes for freedom of movement by moving them back and forth

slightly.

1 2 3 4 5 6 ... 11 12

Indice de contenidos

Pagina 1 - (Part 17256)

FCD WCAIM2034-01(Part 17256)Worcester Controls 10-40 39 Access M Mounted Limit Switch (Proximity Sensor) and SolenoidInstallation, Operation and Maint

Pagina 2

10 10-40 39 Access M Mounted Limit Switch (Proximity Sensor) and Solenoid WCAIM2034Flow Control Worcester ControlsITEM QTY DESCRIPTION1 1 ENCLOSURE2A

Pagina 3

WCAIM2034 10-40 39 Access M Mounted Limit Switch (Proximity Sensor) and Solenoid 11Flow Control Worcester Controls

Pagina 4

Flow Control Worcester ControlsFlowserve Corporation has established industry leadership in the design and manufacture of its products. When properly

Pagina 5

2 10-40 39 Access M Mounted Limit Switch (Proximity Sensor) and Solenoid WCAIM20344. With assembly complete to this point, it is convenient to makecon

Pagina 6

WCAIM2034 10-40 39 Access M Mounted Limit Switch (Proximity Sensor) and Solenoid 3indicating power to the coil and coil continuity, respectively (ifap

Pagina 7

4 10-40 39 Access M Mounted Limit Switch (Proximity Sensor) and Solenoid WCAIM2034A. Limit Switch Ratings:DPDT - 10 amps @ 125/250 VAC; .3 amps @ 125

Pagina 8

WCAIM2034 10-40 39 Access M Mounted Limit Switch (Proximity Sensor) and Solenoid 5Flow Control Worcester Controls

Pagina 9

6 10-40 39 Access M Mounted Limit Switch (Proximity Sensor) and Solenoid WCAIM2034Flow Control Worcester Controls

Pagina 10 - Parts Listing

WCAIM2034 10-40 39 Access M Mounted Limit Switch (Proximity Sensor) and Solenoid 7Flow Control Worcester ControlsCircuit Board Color-Coded Part Number

Pagina 11 - Worcester Controls

8 10-40 39 Access M Mounted Limit Switch (Proximity Sensor) and Solenoid WCAIM2034Flow Control Worcester ControlsThe actuator is electrically fail-saf

Pagina 12

WCAIM2034 10-40 39 Access M Mounted Limit Switch (Proximity Sensor) and Solenoid 9Flow Control Worcester Controls

Comentarios a estos manuales

Sin comentarios

Flowserve 10-40 39 Access M Worcester Controls Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Hardware Flowserve 10-40 39 Access M Worcester Controls. Flowserve 10-40 39 Access M Worcester Controls User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Flowserve 10-40 39 Access M Worcester Controls Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Hardware Flowserve 10-40 39 Access M Worcester Controls. Flowserve 10-40 39 Access M Worcester Controls User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Flowserve 10-40 39 Access M Worcester Controls