Flowserve 1400 Valtek Logix Manual de usuario Pagina 26

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 32
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 25
46-26 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611
Table IV: Transducer Block Signature Parameters (3 of 3)
elbairaV
.oN
elbairaV
renoitisoPxigoL
subdleiF
sepytataD
W/RiLwoLiLpUnoitpircseD
epyTdRtPxiF
641SSERP_TELNItaolfoNtaolfW/RevlavfoerusserpmaertspU
741SSERP_TELTUOtaolfoNtaolfW/RevlavfoerusserpmaertsnwoD
841SGALF_EVLAVrahcdengisnuoN8dengisnUW/R)noitceridwolF.xE(noitamrofnievlaV
941VART_DETARtaolfoNtaolfW/RecivressdeenerofeblevartevlavdetaR
051DI_NAM_TCArahcdengisnuoN23dengisnUW/RrerutcafunamrotautcA
151EPYT_TCArahcdengisnuoN8dengisnUW/RepytrotautcA
251EZIS_TCArahcdengisnuoN8dengisnUW/RezisrotautcA
351EPYT_GNIRPSrahcdengisnuoN8dengisnUW/R.cte,laud,elgnis:epytgnirpS
451DI_LOOPSrahcdengisnuoN8dengisnUW/RnoitacifitnediloopS
551NS_SCINORTCELErahcdengisnuoNgnirtSelbisiV*W/RrebmunlairesscinortcelE
651REV_ERAWTFOStnidengisnuoN61dengisnUW/RnoisrevedocdeddebmerenoitisoP
751NS_EVLAVrahcdengisnuoNgnirtSelbisiVW/RrebmunlairesevlaV
851ETAD_OPrahcdengisnuoNgnirtSelbisiVW/RetadOP
851ETAD_LLATSNIrahcdengisnuoNgnirtSelbisiVW/RetadnoitallatsnI
SDNAMMOCSUOENALLECSIM
171STLUAFED_EE_DAOLrahcdengisnuoN8dengisnU*W/RedometirwMORPEE
271MUN_ESAELER_GNEtnidengisnuoN8dengisnUR rebmunesaelergnireenignededdebmE
371_CSIMSGALFrahcdengisnuoN8dengisnU*W/R
laC-kciuQ,sgalFsuoenallecsiM
elbasiD/elbanE
TAMROFATAD
sretcarahcdengisnu/dengisetyb1 decnavdAdnadradnatShtobnoelbaliavA
sregretnidengisnu/dengissetyb2 ylnosledomdecnavdA
sregretnignoldengisnu/dengissetyb4
)setyb4(taolf457-EEEI
ETIRW/DAER
ylnodaeR=R
sseccaetirW/daeR=W/R
tsumkcolbrecudsnarT=*W/R
etirwotecivresfotuoeb
*Special Note: Because of the internal Database size limit of 10K within the Fieldbus device, the values for RAMP_RATE or STEP_TIME may be recalculated to the most reasonable value to
allow using the database. The new value will appear in the parameter after the desired one is written. This is done to prevent accidental overflow of the database.
It is still possible that the database may overflow, because of timing constraints. If this should happen, SIG_COMPLETE will not appear, but BEGIN_SIG will be turned off. BLOCK_TEST
element 6 will be set to 10 (0x0a) as an error indication. Since this does not affect operation of the positioner itself, no actual error will be reported over Fieldbus.
Vista de pagina 25
1 2 ... 21 22 23 24 25 26 27 28 29 30 31 32

Comentarios a estos manuales

Sin comentarios