Flowserve 510si Series Digital Positioner Manual de usuario

1®User Instructions Logix 510si - LGENIM0510-01 09/09Experience In MotionInstallation OperationMaintenanceLogix 510si SeriesDigital PositionerFCD LGEN

10®User Instructions Logix 510si - LGENIM0510-02 12/13 If the Quick calibration switch is set to Jog, the LED’s will initially flash in a sequence of

11®User Instructions Logix 510si - LGENIM0510-02 12/138.7.2.2 To activate the Binary AO feature: 1. Move the AI/AO calibration dip switch to the AO

12®User Instructions Logix 510si - LGENIM0510-02 12/13 CAUTION: The installation of hazardous location electrical equipment must comply with the pro

13®User Instructions Logix 510si - LGENIM0510-02 12/13Colors Identifier Indication and resolutionG - - -Any sequence starting with a Green light flashin

14®User Instructions Logix 510si - LGENIM0510-02 12/13Colors Identifier Indication and resolutionYRYR 14 Feedback 0 saturated - Calibration error indi

15®User Instructions Logix 510si - LGENIM0510-02 12/1312 TROUBLESHOOTING LOGIX 510SI DIGITAL POSITIONERSFailure Probable Cause Corrective actionNo L

16®User Instructions Logix 510si - LGENIM0510-02 12/1313 SPARE PARTS KITSItem No. Description Part-No.1 Cover Assembly Yellow 255240.999.000White 218

17®User Instructions Logix 510si - LGENIM0510-02 12/13Figure 7: Exploded drawing for spare parts1234

18®User Instructions Logix 510si - LGENIM0510-02 12/13Figure 8: Dimensional Drawing for the Logix 500si Series Digital Positioner3.998.14LED WINDOWFR

19®User Instructions Logix 510si - LGENIM0510-01 09/098.51216.183.94100.001/4" NPTSINGLE PRESSURE GAUGEAUXILIARY OPTIONS - “GA” (GAUGE ADAPTER)3.

2®User Instructions Logix 510si - LGENIM0510-02 12/131 USING FLOWSERVE VALVES, ACTUATORS AND ACCESSORIES CORRECTLY1.1 Using The following instruction

20®User Instructions Logix 510si - LGENIM0510-02 12/13All data subject to change without notice© ©02.2009 Flowserve Corporation. Flowserve and Kämmer

3®User Instructions Logix 510si - LGENIM0510-02 12/131.6 Spare parts Use only FLOWSERVE original spare parts. FLOWSERVE cannot accept responsibility

4®User Instructions Logix 510si - LGENIM0510-02 12/134 SPECIFICATIONSTable 1: Input SignalInput Signal Range 4 - 20 mACompliance Voltage 6 VD

5®User Instructions Logix 510si - LGENIM0510-02 12/13Figure 1: Logix 510si Principle of Operationfor all applications due to the close tolerances in t

6®User Instructions Logix 510si - LGENIM0510-02 12/137 WIRING AND GROUNDING GUIDELINES Electrical connections: signal cable with cable passage (NPT,

7®User Instructions Logix 510si - LGENIM0510-02 12/13The Logix 510si requires that the current loop system allow for a 6,0 VDC drop across the positio

8®User Instructions Logix 510si - LGENIM0510-02 12/13 NOTE: The switch settings in the Configuration box are activated only by pressing the Quick-Ca

9®User Instructions Logix 510si - LGENIM0510-02 12/13UÊ vÊ ÌiÊ ÀÌ>ÀÞÊ º>»Ê ÃiiVÌÀÊ ÃÜÌVÊ ÃÊ ÃiÌÊ ÌÊ ºE” with the auto tune switch o